|
Internet Search Results
Removing Limescale Buildup on Aluminum Boat - GlobalSpec
Re: Removing Limescale Buildup on Aluminum Boat. You are creating CaCO2, Mg (OH)3, Aluminum Oxide, ect. due to the corrosion and electrolysis of Aluminum metal in the salt (ionized solution) water. best way to prevent this as others have stated, coat the aluminum metal with a non-conducting coating.
CR4 - Blog Entry: Four Ways to Cut Rubber Products
Manual cutting is the simplest way to cut industrial rubber products. Often, a box cutter or bladed knife is used. An employee removes material from inventory, positions the sheet or profile on a work surface such as table, and then creates a stencil or template for use during cutting. With edge trim that contains metal wire, guillotine cutting ...
How To Install a Check Valve in Drain Pipe? - GlobalSpec
Re: CHECK VALVE. 01/05/2020 3:30 AM. The horizontal pipe should be at a slight downward angle to allow draining of that section. I would fit the check valve in a vertical section as gunk would be more likely to build up in a horizontal pipe, and vertically would give a more even pressure around the seal.
What is Welding Arc Flash and How Can it be Prevented? - GlobalSpec
Pathfinder Tags: radwell Welding. Welding arc flash is a burn of the outer layers of the eyeball caused by the intense ultra-violet radiation generated by welding. A common cause of arc flashes in the industrial industry is when someone looks directly at the welding area without wearing protective eye gear. Directly looking at the UV radiation ...
Gorilla Glue on Vinyl Fence Posts - CR4 Discussion Thread - GlobalSpec
In reply to #2. Re: Gorilla glue on vinyl fence posts. 11/02/2020 7:56 AM. this IS the answer to repairing your fence. i wouldn't mess with the standard polyurethane formula. as it expands it will extrude out of the joint and if the fence is white, you will have to now try to remove the baby food color.
Old Markon Generator Trouble - CR4 Discussion Thread - GlobalSpec
Join CR4, The Engineer's Place for News and Discussion! These comments received enough positive ratings to make them "good answers". #1 "Re: Old Markon generator, trouble" by SolarEagle on 01/28/2020 1:08 AM (score 2) #2 "Re: Old Markon generator, trouble" by SolarEagle on 01/28/2020 1:34 AM (score 2) 2. SolarEagle.
1979 KZ1000 Clutch Problem - CR4 Discussion Thread - GlobalSpec
Re: 1979 KZ1000 Clutch Problem. 07/08/2014 9:44 AM. If it were me that owned the bike, i would just change out the clutch plates myself. it is rather easy. drain oil. remove clutch cable. remove clutch plate cover. remove clutch plate basket cover. remove and replace plates in same order as removed. reuse metal discs.
2000 Lesabre Has No Heat - CR4 Discussion Thread - GlobalSpec
The core is clogged with minerals or scale. If the core is leaking, you can test it by sealing the inlet and outlet and putting it into a bucket of water. If you see bubbles, then the core is leaking, you can also pressurize it with the air compressor with about 20 psi. Bubbles equals a leak, no bubbles, no leak.
Gasoline to Natural Gas Conversion for Briggs and Stratton
Re: Gasoline to Natural Gas Conversion for Briggs and Stratton. 10/16/2020 5:13 AM. Yes, a gasoline engine will run on LP or natural gas,but the expected output is reduced accordingly. There are many kits available on line,including dual-fuel models. All kits include a de-rating chart.
Soft-Touch on Plastic Material - CR4 Discussion Thread - GlobalSpec
Temperature extremes and UV exposure. soft materials lose plasticizers which are usually shorter chained polymers. In the heat and UV exposure these softeners outgas and leave the material brittle. Toss in thermal expansion from heating and cooling, as well as mechanical bending and stretching and you get cracks.
|
